Easy Make a Lights On! Schematic

This circuit ensures that you will never again forget to switch on the lights of your car. As soon as the engine is running, the dipped beams and the sidelights are automatically switched on. The circuit also causes the dipped beams to be extinguished as soon as the main beams are switched on. As you can see from the schematic diagram, no special components are needed.

When the engine is running, the alternator will generate a voltage of more than 14 V. Diode D1 reduces this voltage by 5.6 V and passes it to the base of T1 via R1. Due to the resulting current, T1 conducts. The amplified current flows via R3, the base of T3 and D3 to ground. This causes T3 to also conduct and energize relay Re1.

Lights On  Circuit Diagram :

If the driver now switches on the main beams, a current flows through D2 and R2 into the base of T2, causing this transistor to conduct. As a result, the voltage on the base of T3 drops, causing T3 to cut off and the relay to drop out.

When the main beams are switched off, the previous situation is restored, and the relay again engages. The dipped beams and the sidelights are switched by the contacts of relay Re1. Diodes D5 and D6 ensure that the sidelights are illuminated if either the dimmed beams or the main beams are switched on. In practice, this means that the sidelights will be on whenever the engine is running, regardless of whether the main beams are switched on.

Read More

Simple Tone Booster Schematic Diagram

This is the tone booster schematic diagram which is published on Everyday Electronics, September 1978 edition. The peaks of frequencies is at 5000 Hz for a “cleaner and more penetrating” sound. The Q1 type is ztx384, while the Q2 is BC415p.

 Simple Tone Booster Schematic Diagram

Read More

Schematic Audio Power Amplifier with IC TDA2822

TDA2822 is manufactered by PHILIPS , its based on this amplifier . Minimum voltage 3 volts and maximum voltage 15 volts. Power output 2 x 1,8 stereo with 4 Ohm impedance. Quiescent current 6 mA , sensitive input is 30 Hz to 18 kHz. See circuit diagram below :

Read More

Easy LED Flasher Schematic

Here the schematic diagram of Easy LED Flasher schema:

Parts List:

R1 = 10M ohm R2 = 1K – 100K ohm R3 = 470 ohm C1 = 0.47μF – 10μF/25V

D1 = 1N914 Q1 = 2N3904 Q2 = 2N3906 Led = High Brightness Red LED

This schema will flash a bright or high-brightness red LED (5000+ mcd). Very good for fake car alarm or other attention getting device. Part values are not significant, test something else to start with from your junkbox.Certainly, the 470 ohm resistor (R3) determines the LEDs brightness and limits the current supply to around 20mA. R3 value of 390 ohm may also be applied as a save value.

If you decide to go using a green or yellow led, which take more current, you might want to change the 470 ohm with an suitable value. Flash speed is established by R2 and C1 and is roughly three time constants (3*R2*C1). R1 provides bias to Q1 which ought to be small enough not to saturate Q2 with the capacitor disconnected. When the schema doesnt oscillate, R1 may be very low or R2 too high. D1 allows for highter duty cycle operation and limits the feedback at the base of Q1 to -0.7 volts. D1 might be ommited for low supply power like 6 - 9V and low duy cycle operation.

Read More

Schematic Audio Amplifer with IC AN315

This Schematic Require voltage 9 - 18 Volt. Good voltage for this schematic is 12 V. This is Mono amplifier with output 5,5 Watt and impedance 8 Ohm. You can make this Circuit easily because i give simple and clear scheme.

See this Schematic and Datsheet IC AN315 :

Click to Enlarge

Datasheet IC AN315

Vcc                = 9-18 V

Pout               = 5,5 W

RL                  = 8 Ohm

Ft                   = 30hz - 18Khz

Icco                = 28 mA

Package         = SIP2-11

Manufactered = MATSUSHITA

Read More